 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| il715/IL716/il717 isoloop is a registered trademark of nve corporation. *u.s. patent numbers 5,831,426; 6,300,617 and others. rev. aa nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation high speed four-channel digital isolators functional diagrams il715 IL716 il717 in 1 in 2 out 3 out 4 out 1 out 2 in 3 in 4 out 1 out 2 out 3 in 4 out 1 out 2 out 3 out 4 in 1 in 2 in 3 in 4 in 1 in 2 in 3 out 4 features ? high speed: 110 mbps ? high temperature: ? 40c to +125c (?t? and ?v? series) ? high isolation voltage: 5 kv rms per ul 1577 (v-series) ? high working voltage: 1 kv rms per vde 0884 (v-series) ? 50 kv/ s typ.; 30 kv/ s min. common mode transient immunity ? no carrier or clock for low em i emissions and susceptibility ? 1.2 ma/channel typical quiescent current ? 100 ps pulse jitter ? 2 ns channel-to-channel skew ? 10 ns typical pr opagation delay ? 44000 year barrier life ? excellent magnetic immunity ? vde 0884 / iec 60747-5-5 certified; ul 1577 recognized ? 0.15", 0.3", and true 8? mm 16-pin soic; 16-pin qsop packages applications ? adcs and dacs ? digital fieldbus ? multiplexed data transmission ? board-to-board communication ? ground loop elimination ? parallel bus ? logic level shifting ? equipment covered under iec 61010-1 edition 3 ? 5 kv rms rated iec 60601-1 medical applications description n ve?s il715, IL716, and il717 fou r -channel high-speed digital isolators are cmos devices manufactured with nve?s patented* isoloop ? spintronic giant magnetoresistive (gmr) technology. a unique ceramic/polymer composite barrier provides excellent isolation and virtually unlimited barrier life. all transmit and receive channels operate at 110 m bps over the full temperature and supply voltage range . the symmetric magnetic coupling barrier provides a typical propagation delay of only 10 ns and a pulse width distortion of 2 ns, achieving the best specifications of any isolator. typical transient immunity of 50 kv/s is unsurpassed. high channel density makes these devices ideal fo r isolating adcs and dacs, parallel buses and peripheral interfaces. the il715, IL716, and il717 are available in 16-pin 0.3" and 0.15" soic, and ultraminiature qsop packages. performance is specified over a temperature range of ? 40c to +100c. ?t? and ?v? series parts have a ma ximum operating temperature of 125c. v-series versions offer high isolation voltage of 5 kv rms .
il715/IL716/il717 2 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation absolute maximum ratings parameters symbol min. typ. max. units test conditions storage temperature t s ? 55 150 c junction temperature t j ? 55 150 c ambient operating temperature ( 1 ) ?t? and ?v? versions t a ? 40 100 125 c supply voltage v dd 1 , v dd 2 ? 0.5 7 v input voltage v i ? 0.5 v dd +0.5 v output voltage v o ? 0.5 v dd +0.5 v output current drive i o 10 ma lead solder temperature 260 c 10 sec. esd 2 kv hbm recommended operating conditions parameters symbol min. typ. max. units test conditions ambient operating temperature ?t? and ?v? versions t a ? 40 100 125 c junction temperature ?t? and ?v? versions t j ? 40 110 125 c supply voltage v dd 1 , v dd 2 3.0 5.5 v logic high input voltage v ih 2.4 v dd v logic low input voltage v il 0 0.8 v input signal rise and fall times t ir , t if 1 s insulation specifications parameters symbol min. typ. max. units test conditions creepage distance (external) qsop 0.15" soic 0.3" soic 4.03 4.03 8.03 8.3 mm per iec 60601 total barrier thickness (inter nal) 0.012 0.013 mm leakage current ( 5 ) 0.2 a 240 v rms , 60 hz barrier resistance ( 5 ) >10 14 ? 500 v barrier capacitance ( 5 ) 4 pf f = 1 mhz comparative tracking index cti 175 v per iec 60112 high voltage endurance (maximum barrier voltage for indefinite life) ac dc v io 1000 1500 v rms v dc at maximum operating temperature barrier life 44000 years 100c, 1000 v rms , 60% cl activation energy thermal characteristics parameter symbol min. typ. max. units test conditions junction?ambient thermal resistance qsop 0.15" soic 0.3" soic ja 60 60 60 c/w soldered to double- sided board; free air junction?case (top) thermal resistance qsop 0.15" soic 0.3" soic jt 10 10 20 c/w power dissipation qsop 0.15" soic 0.3" soic p d 675 700 800 mw il715/IL716/il717 3 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation safety and approvals vde 0884-10 (file number 5016933-4880-0001; v-series 5 kv-rated parts) ? working voltage (v iorm ) 1000 v rms (1415 v pk ); basic insulation; pollution degree 2 ? transient overvoltage (v iotm ) 6000 v pk ? surge voltage (v iosm ) 10 kv pk ? each part tested at 2387 v pk for 1 second, 5 pc partial discharge limit ? samples tested at 6000 v pk for 60 sec.; then 2122 v pk for 10 sec. with 5 pc partial discharge limit iec 60747-5-5 (vde 0884) (file number 5016933-4880-0001; 2.5 kv-rated parts) ? working voltage (v iorm ) 600 v rms (848 v pk ); basic insulation; pollution degree 2 ? transient overvoltage (v iotm ) and surge voltage (v iosm ) 4000 v pk ? each part tested at 1590 v pk for 1 second, 5 pc partial discharge limit ? samples tested at 4000 v pk for 60 sec.; then 1358 v pk for 10 sec. with 5 pc partial discharge limit vde 0884-10 / iec 60747-5-5 safety-limiting values safety-limiting values symbol value units safety rating ambient temperature t s 180 c safety rating power (180c) p s 270 mw supply current safety rating (total of supplies) i s 54 ma iec 61010-1 (edition 2; tuv certificate numbers n1502812; n1502812-101) reinforced insulation; pollution degree ii; material group iii part no. suffix package working voltage -1 qsop 300 v rms -3 0.15" soic 300 v rms none 0.3" soic (standard) 300 v rms v 0.3" soic (high isolation voltage) 1000 v rms ul 1577 (component recognition progr am file number e207481) ? 5 kv-rated v-series parts tested at 6 kv rms (8480 v pk ) for 1 second; each lot sample tested at 5 kv rms (7060 v pk ) for 1 minute ? 2.5 kv-rated parts tested at 3000 v rms (4240 v pk ) for 1 second; each lot sample tested at 2500 v rms (3530 v pk ) for 1 minute soldering profile per jedec j-std-020c, msl 1 il715/IL716/il717 4 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation il715 pin connections 1 v dd1 supply voltage 2 gnd 1 ground return for v dd 1 * 3 in 1 data in, channel 1 4 in 2 data in, channel 2 5 in 3 data in, channel 3 6 in 4 data in, channel 4 7 nc no connection 8 gnd 1 ground return for v dd 1 * 9 gnd 2 ground return for v dd 2 * 10 nc no connection 11 out 4 data out, channel 4 12 out 3 data out, channel 3 13 out 2 data out, channel 2 14 out 1 data out, channel 1 15 gnd 2 ground return for v dd 2 * 16 v dd2 supply voltage v dd1 gnd 1 gnd 2 out 2 out 3 out 1 in 1 in 2 in 3 v dd2 in 4 nc nc out 4 gnd 1 gnd 2 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 il715 IL716 pin connections 1 v dd1 supply voltage 2 gnd 1 ground return for v dd 1 * 3 in 1 data in, channel 1 4 in 2 data in, channel 2 5 out 3 data out, channel 3 6 out 4 data out, channel 4 7 nc no connection 8 gnd 1 ground return for v dd 1 * 9 gnd 2 ground return for v dd 2 * 10 nc no connection 11 in 4 data in, channel 4 12 in 3 data in, channel 3 13 out 2 data out, channel 2 14 out 1 data out, channel 1 15 gnd 2 ground return for v dd 2 * 16 v dd2 supply voltage v dd1 gnd 1 gnd 2 out 2 out 3 out 1 in 1 in 2 in 3 v dd2 in 4 nc nc out 4 gnd 1 gnd 2 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 IL716 *note: pins 2 and 8 are internally connected, as are pins 9 and 15. il715/IL716/il717 5 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation il717 pin connections 1 v dd1 supply voltage 2 gnd 1 ground return for v dd 1 * 3 in 1 data in, channel 1 4 in 2 data in, channel 2 5 in 3 data in, channel 3 6 out 4 data out, channel 4 7 nc no connection 8 gnd 1 ground return for v dd 1 * 9 gnd 2 ground return for v dd 2 * 10 nc no connection 11 in 4 data in, channel 4 12 out 3 data out, channel 3 13 out 2 data out, channel 2 14 out 1 data out, channel 1 15 gnd 2 ground return for v dd 2 * 16 v dd2 supply voltage *note: pins 2 and 8 are internally c onnected, as are pins 9 and 15. v dd1 gnd 1 gnd 2 out 2 out 3 out 1 in 1 in 2 in 3 v dd2 in 4 nc nc out 4 gnd 1 gnd 2 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 il717 timing diagram legend t plh propagation delay, low to high t phl propagation delay, high to low t pw minimum pulse width t r rise time t f fall time il715/IL716/il717 6 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation 3.3 volt electrical specifications (t min to t max unless otherwise stated) parameters symbol min. typ. max. units test conditions input quiescent supply current il715 and il715-3 i dd1 16 20 a il715-1 300 400 a IL716 2.4 3.5 ma il717 1.2 1.75 ma output quiescent supply current il715 i dd2 4.8 7 ma IL716 2.4 3.5 ma il717 3.6 5.25 ma logic input current i i ? 10 10 a logic high output voltage v oh v dd ? 0.1 v dd v i o = ? 20 a, v i = v ih 0.8 x v dd 0.9 x v dd i o = ? 4 ma, v i = v ih logic low output voltage v ol 0 0.1 v i o = 20 a, v i = v il 0.5 0.8 i o = 4 ma, v i = v il switching specifications (v dd = 3.3 v) maximum data rate 100 110 mbps c l = 15 pf pulse width ( 7 ) pw 10 ns 50% points, v o propagation delay input to output (high to low) t phl 12 18 ns c l = 15 pf propagation delay input to output (low to high) t plh 12 18 ns c l = 15 pf pulse width distortion ( 2 ) pwd 2 3 ns c l = 15 pf propagation delay skew ( 3 ) t ps k 4 6 ns c l = 15 pf output rise time (10% ? 90%) t r 2 4 ns c l = 15 pf output fall time (10% ? 90%) t f 2 4 ns c l = 15 pf common mode transient immunity (output logic high or logic low) (4) |cm h |,|cm l | 30 50 kv/s v cm = 1500 v dc t transient = 25 ns channel-to-channel skew t csk 2 3 ns c l = 15 pf dynamic power consumption ( 6 ) 140 240 a/mbps per channel magnetic field immunity ( 8 ) (v dd2 = 3v, 3v il715/IL716/il717 8 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation application information electrostatic disch arge sensitivity this product has been tested for electrostatic sensitivity to the limits stated in the specifications. however, nve recommends that all integrated circuits be handled with appropriate care to avoid damage. damage caused by inappr opriate handling or storage could range from performance degrad ation to complete failure. electromagnetic compatibility isoloop isolators have the lowest emc footprint of any isolation technology. isoloop isolators? wheatstone bridge configuration and differential magnetic field signaling ensure excellent emc performance against all relevant standards. these isolators are fully compliant with generic emc standards en50081, en50082-1 and the umbrella line-voltage standard for information technology equipment (ite) en61000. nve has completed compliance tests in the categories below: en50081-1 residential, commercia l & light industrial methods en55022, en55014 en50082-2: industrial environment methods en61000-4-2 (esd), en61000-4-3 (electromagnetic field immunity), en61000-4-4 (ele ctrical transien t immunity), en61000-4-6 (rfi immunity), en61000-4-8 (power frequency magnetic field immunity), en61000-4-9 (pulsed magnetic field), en61000-4-10 (damped oscillatory magnetic field) env50204 radiated field from digita l telephones (immunity test) immunity to external magnetic fields is even higher if the field direction is ?end-to-end? rather than to ?pin-to-pin? as shown in the diagram below: cross-axis field direction dynamic power consumption isoloop isolators achieve their low power consumption from the way they transmit data across the isolation barrier. by detecting the edge transitions of the input logic signal and converting these to narrow current pulses, a magnetic field is created around the gmr wheatstone bridge. depending on the direction of the magnetic field, the bridge causes the output comparator to switch following the input logic signal. since the current pulses are narrow, about 2.5 ns, the power consumption is independent of mark-to-space ratio and solely dependent on frequency. this has obvious advantages over optocouplers, which have power consumption heavily dependent on mark-to-space ratio. thermal management isoloop isolators are designed for low power dissipation and thermal performance, providing unmatched channel density for high-performance isolators. nevert heless, package temperature rise should be considered when running multiple channels at high speed. power consumption is higher at 5 volt operation than at 3.3 volts, and dynamic supply current is higher on the input side of the isolators than the output side, so thermal management is more important with five-volt input-side power supplies. based on the specifications contained in this datasheet, the derating curve at typical operating conditions is as follows: standard-grade parts have a maximum junction temperature of 110c. t-series parts have a maximum operating junction temperature of 125c for additional margin at extreme operating conditions. power supply decoupling both power supplies to these devi ces should be decoupled with low esr 47 nf ceramic capacitors. ground planes for both gnd 1 and gnd 2 are highly recommended for data rates above 10 mbps. capacitors must be located as close as possible to the v dd pins. maintaining creepage creepage distances are often critical in isolated circuits. in addition to meeting jedec standards, nve isolator packages have unique creepage specifications. standard pad libraries often extend under the package, compromising creepage and clearance. similarly, ground planes, if used, should be spaced to avoid compromising clearance. package drawings and recommended pad layouts are included in this datasheet. signal status on start-up and shut down to minimize power dissipation, i nput signals are differentiated and then latched on the output side of the isolation barrier to reconstruct the signal. this could result in an ambiguous output state depending on power up, shutdown and power loss sequencing. therefore, the designer should cons ider including an initialization signal in the start-up circuit. ini tialization consists of toggling the input either high then low, or low then high. il715/IL716/il717 9 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation application diagrams isolated logic level shifters cs clk di do sensor adc il717 controller +5v +3.3v gnd 1 gnd 2 single-channel isolated de lta-sigma a/d converter bridge + serial data out serial data in data clock chip select iso sd out iso sd in iso data clock iso cs bridge - osc 2 il717 cs5532 clock generator bridge bias delta sigma a/d isolation boundary this circuit illustrates a typical single-channel delta-sigma adc . the a/d is located on the bridge with no signal conditioning electronics between the bridge sensor and the adc. in this case, the il717 is the best choice for isolation. it isolates the control bus fr om the microcontroller. the system clock is located on the isolated side of the system. il715/IL716/il717 10 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation package drawings ultraminiature 16-pin qsop package (-1 suffix) 0.188 (4.77) 0.197 (5.00) 0.025 (0.635) 0.004 (0.10) 0.010 (0.25) note: pin spacing is a basic dimension; tolerances do not accumulate 0.060 (1.52) 0.069 (1.75) 0.228 (5.8) 0.244 (6.2) 0.150 (3.8) 0.157 (4.0) 0.050 (1.27) 0.056 (1.42) 0.013 (0.3) 0.020 (0.5) 0.007 (0.20) 0.010 (0.25) 0.020 (0.50) 0.029 (0.75) nom dimensions in inches (mm); scale = approx. 5x 0.15" 16-pin soic package (-3 suffix) 0.386 (9.8) 0.394 (10.0) 0.049 (1.24) 0.051 (1.30) 0.007 (0.2) 0.013 (0.3) pin 1 identified by either an indent or a marked dot 0.004 (0.1) 0.012 (0.3) 0.016 (0.4) 0.050 (1.3) note: pin spacing is a basic dimension; tolerances do not accumulate 0.054 (1.4) 0.072 (1.8) 0.228 (5.8) 0.244 (6.2) 0.150 (3.81) 0.157 (3.99) 0.055 (1.40) 0.062 (1.58) 0.013 (0.3) 0.020 (0.5) nom dimensions in inches (mm); scale = approx. 5x il715/IL716/il717 11 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation 0.3" 16-pin soic package (no suffix) 0.049 (1.24) 0.051 (1.30) 0.017 (0.43)* 0.022 (0.56) 0.292 (7.42)* 0.299 (7.59) 0.007 (0.18)* 0.010 (0.25) 0.260 (6.60)* 0.280 (7.11) 0.033 (0.85)* 0.043 (1.10) 0.007 (0.2) 0.013 (0.3) pin 1 identified by either an indent or a marked dot 0.08 (2.0) 0.10 (2.5) 0.397 (10.08) 0.413 (10.49) 0.394 (10.00) 0.419 (10.64) 0.092 (2.34) 0.105 (2.67) 0.004 (0.1) 0.012 (0.3) 0.016 (0.4) 0.050 (1.3) note: pin spacing is a basic dimension; tolerances do not accumulate 0.013 (0.3) 0.020 (0.5) dimensions in inches (mm); scale = approx. 5x *specified for true 8? package to guarantee 8 mm creepage per iec 60601. il715/IL716/il717 12 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation recommended pad layouts 4 mm x 5 mm 16-pin qsop pad layout 0.275 (6.99) 0.025 (0.635) dimensions in inches (mm); scale = approx. 5x 0.160 (4.05) 0.012 (0.30) 16 plcs 0.15" 16-pin soic pad layout 0.050 (1.27) 0.275 (6.99) 0.020 (0.51) 16 plcs 0.160 (4.06) dimensions in inches (mm); scale = approx. 5x il715/IL716/il717 13 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation 0.3" 16-pin soic pad layout 0.050 (1.27) 0.449 (11.40) 0.020 (0.51) 16 plcs 0.317 (8.05) dimensions in inches (mm); scale = approx. 5x il715/IL716/il717 14 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation ordering information il 716 t - 3 e tr13 bulk packaging blank = tube tr7 = 7'' tape and reel tr13 = 13'' tape and reel package blank = 80/20 tin/lead plating e = rohs compliant package type blank = 0.30'' 16-pin soic -1 = 0.15'' 16-pin qsop -3 = 0.15'' 16-pin soic grade blank = standard temperature (100c) and isolation voltage (2.5 kv) t = high temperature (125c) v = high isolation voltage (5 kv) and high temperature (125c) base part number 715 = 4 transmit channels 716 = 2 transmit channels 2 receive channels 717 = 3 transmit channels 1 receive channel product family il = isolators il715/IL716/il717 15 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation available parts available parts transmit channels receive channels maximum temperature isolation voltage (rms) package rohs il715-1e 4 0 100c 2.5 kv qsop y il715-3 4 0 100c 2.5 kv narrow soic n il715-3e 4 0 100c 2.5 kv narrow soic y il715 4 0 100c 2.5 kv wide soic n il715e 4 0 100c 2.5 kv wide soic y il715t-3 4 0 125c 2.5 kv narrow soic n il715t-3e 4 0 125c 2.5 kv narrow soic y il715t 4 0 125c 2.5 kv wide soic y il715te 4 0 125c 2.5 kv wide soic n il715ve 4 0 125c 5 kv wide soic y IL716-1e 2 2 100c 2.5 kv qsop n IL716-3 2 2 100c 2.5 kv narrow soic n IL716-3e 2 2 100c 2.5 kv narrow soic y IL716 2 2 100c 2.5 kv wide soic n IL716e 2 2 100c 2.5 kv wide soic y IL716t-3 2 2 125c 2.5 kv narrow soic n IL716t-3e 2 2 125c 2.5 kv narrow soic y IL716t 2 2 125c 2.5 kv wide soic n IL716te 2 2 125c 2.5 kv wide soic y IL716ve 2 2 125c 5 kv wide soic y il717-1e 3 1 100c 2.5 kv qsop y il717-3 1 1 100c 2.5 kv narrow soic n il717-3e 3 1 100c 2.5 kv narrow soic y il717 3 1 100c 2.5 kv wide soic n il717e 3 1 100c 2.5 kv wide soic y il717t-3 3 1 125c 2.5 kv narrow soic n il717t-3e 3 1 125c 2.5 kv narrow soic y il717t 3 1 125c 2.5 kv wide soic n il717te 3 1 125c 2.5 kv wide soic y il717ve 3 1 125c 5 kv wide soic y all part types are available on tape and reel. il715/IL716/il717 16 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation isb-ds-001-il715/6/7-aa september 2014 changes ? added v-series 5 kv isolation voltage versions. ? more detailed ?available parts? table. isb-ds-001-il715/6/7-z changes ? added package illustrations on first page. ? added qsop packages (-1 suffix). ? revised and added details to thermal ch aracteristic specifications (p. 2). ? added vde 0884 safety-limiting values (p. 3). ? added ?thermal management? paragr aph in applications section. isb-ds-001-il715/6/7-y changes ? iec 60747-5-5 (vde 0884) certification. isb-ds-001-il715/6/7-x changes ? tighter quiescent current specifications. ? upgraded from msl 2 to msl 1. isb-ds-001-il715/6/7-w changes ? increased transient immunity specifications based on additional data. ? added vde 0884 pending. ? added high voltage endurance specification. ? increased magnetic immunity specifications. ? updated package drawings. ? added recommended solder pad layouts. isb-ds-001-il715/6/7-v changes ? detailed isolation and barrier specifications. ? cosmetic changes. isb-ds-001-il715/6/7-u changes ? tightened typical output quiescent suppl y spec. to 1.5 ma/channel at 3.3v. isb-ds-001-il715/6/7-t changes ? updates to terms and conditions. isb-ds-001-il715/6/7-s changes ? added clarification of internal ground connections (pp. 3-4). isb-ds-001-il715/6/7-r changes ? added typical jitter specification at 5v. isb-ds-001-il715/6/7-q changes ? added emc details. isb-ds-001-il715/6/7-p changes ? added magnetic field immuni ty and electromagnetic compatibility specifications. ? added notes on package drawings that pi n-spacing tolerances are non-accumulating. il715/IL716/il717 17 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation datasheet limitations the information and data provided in datasheets shall define the specification of the product as agreed between nve and its cus tomer, unless nve and customer have explicitly agreed otherwise in writing. all specifica tions are based on nve test protocols. in no event however, shall an agreement be valid in which the nve product is deemed to offer func tions and qualities beyond those described in the datasheet. limited warranty and liability information in this document is believed to be accurate and reliable. however, nve do es not give any representations or warrant ies, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. in no event shall nve be liable for any indirect, incidental, pu nitive, special or consequential damages (including, without li mitation, lost profits, lost savings, business interruption, costs related to the removal or repl acement of any products or rewo rk charges) whether or not s uch damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. right to make changes nve reserves the right to make changes to information publishe d in this document including, without limitation, specifications and product descriptions at any time and without notice. this document supersedes an d replaces all information supplied prior to its publication. use in life-critical or safety-critical applications unless nve and a customer explicitly agree otherwise in writing, nv e products are not designed, aut horized or warranted to be s uitable for use in life support, life-critical or safety-critical devices or equipment. nve accepts no liability for inclusion or use of nve products i n such applications and such inclusion or use is at the customer?s own risk. should the customer use nve products for such application whether authorized by nve or not, the customer shall indemnify and hold nve harmless against all claims and damages. applications applications described in this datasheet are illustrative only. nv e makes no representation or wa rranty that such applications will be suitable for the specified use without furthe r testing or modification. customers are responsible for the design and operation of their a pplications and products using nve products, and nve accepts n o liability for any assistance with applications or customer product design. it is customer?s sole res ponsibility to determine whether the nve prod uct is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party cust omers. customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nve does not accept any liability related to an y default, damage, costs or problem whic h is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer s. the customer is responsible for all ne cessary testing for the customer?s applications and products using nve products in order to avoid a default of the applications and the products or of the application or use by customer?s third party customers. nve accepts no liability in this respect. limiting values stress above one or more limiting values (as defined in the abso lute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the recommended operating conditions of the datasheet is not warranted. constant or repeated exposure to limiting values will permanently and i rreversibly affect the quality and reliability of the device. terms and conditions of sale in case an individual agreement is concl uded only the terms and conditions of the respective agreement shall apply. nve hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nve products by customer. no offer to sell or license nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. export control this document as well as the items described herein may be s ubject to export control regulati ons. export might require a prior authorization from national authorities. automotive qualified products unless the datasheet expressly states that a specific nve product is automotive qualified, the product is not suitable for auto motive use. it is neither qualified nor tested in accordance with automotive testing or application requirements. nve accepts no liability for inclusion or use of non-automotive qualified products in automotive equipment or applications. in the event that customer uses the product for design-in and us e in automotive applications to automotive specifications and s tandards, customer (a) shall use the product without nve?s warranty of the product for such automotive applicati ons, use and specifications, and (b) wheneve r customer uses the product for automotive applications beyond nve?s specifications such use shall be solely at customer?s own risk, and (c) custom er fully indemnifies nve for any liability, damages or failed product claims resulting fro m customer design and use of the product for automotive ap plications beyond nve?s standard warranty and nve?s product specifications. il715/IL716/il717 18 nve corporation 11409 valley view road, eden prairie, mn 55344-3617 phone: (952) 829-9217 fax: (952) 829-9189 www.isoloop.com ?nve corporation an iso 9001 certified company nve corporation 11409 valley view road eden prairie, mn 55344-3617 usa telephone: (952) 829-9217 fax: (952) 829-9189 www.nve.com e-mail: iso-info@nve.com ?nve corporation all rights are reserved. reproduction in whole or in part is prohibited without the prior writte n consent of the copyright owne r. isb-ds-001-il715/6/7-aa september 2014 |
Price & Availability of IL716
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |